Panasonic WV-SW396 User Manual (en)

Download
• 24 V AC power supply connector kit (accessory)
Recommended specification of cable (wire)
Wire size 
(AWG), 
stranded 
wire
#24
(0.22 mm)
#22
(0.33 mm)
#20
(0.52 mm)
#18
(0.83 mm)
Length of 
cable
20 m  
{65.62 feet}
30 m  
{98.43 feet}
45 m  
{147.64 feet}
75 m 
{246.06 feet}
Terminals of the power supply connector
Pin No.
Signal
1
2
3
4
24 V AC LIVE
24 V AC NEUTRAL
Ground
Not use
• How to assemble the power supply connector
Remove approx. 3 mm {1/8 inches} of the outer jacket of 
the cable and twist the cable core to prevent the short cir-
cuit first.
Insert the tip of the cable into the point A of the contact, 
and hold the cable using the cable clamp. 
Procure either of the following tools for clamping. 
Molex manual clamp tool:
  
57027-5000 (for UL1015), 57026-5000 (for UL1007)
After clamping the contact and the cable, insert the con-
tact properly into the power supply connector housing. 
Important:
 •  Conduct  the  electric  conduit  work  after  processing
the power supply connector and making sure that the 
camera is operating normally. 
 
    
• Network cable
Connect a LAN cable (category 5e or better, STP*) to the 
network connector. 
* E model only
Important:
 •  Use all 4 pairs (8 pins) of the LAN cable.
 •  The maximum cable length is 100 m {328 feet}.
 •  Make  sure  that  the  PoE+  device  in  use  is  compliant
with IEEE802.3at standard. 
 •  When connecting both of the 24 V AC power supply
and the PoE+ device for power supply, 24 V AC will 
be used for power supply. 
  
Depending on PoE+ (or PoE) devices, the power sup-
ply indicator may light or the network functions may 
be unavailable. 
  
In this case, disable the PoE+ (or PoE) settings. Refer 
to the operating instructions of the PoE+ (or PoE) 
device in use.
 
• Output cable for the monitor used for adjustment
Connect a coaxial cable (BNC) (only for checking if images 
are displayed on the monitor). 
This output is provided only for checking the adjustment 
of the angular field of view on the video monitor when 
installing the camera or when servicing. 
Important:
 •  The monitor out connector for adjustment is provided
only for checking the adjustment of the angular field 
of view on the video monitor when installing the cam-
era or when servicing. It is not provided for recording/
monitoring use.
 •  Black  bands  may  appear  at  the  top  and  bottom  or
right and left of the screen. (That does not affect the 
adjustment because the angular field of view is not 
changed.)
 
• External I/O cable
Important:
 •  Input and output of the external I/O terminal 2 and 3
can be switched by configuring the setting. The 
default of EXT I/O terminal 2 is "ALARM IN 2" and of 
EXT I/O terminal 3 is "ALARM IN 3". It is possible to 
determine whether or not to receive input from EXT 
I/O terminal 2 and 3 (ALARM IN2, 3) by selecting 
"Off", "Alarm input", "Alarm output" or "AUX output" 
for "Terminal alarm 2" or "Terminal alarm 3" on the 
[Alarm] tab on the "Alarm" page. Refer to the 
Operating Instructions (included in the CD-ROM) for 
further information. 
 •  When using the EXT I/O terminals as the output termi-
nals, ensure they do not cause signal collision with 
external signals. 
 
Contact
Insert
Upper 
side
A
Approx. 3 mm {1/8 inches}
Cable
1
3
2
4
Contact
Power supply connector housing (accessory)
Upper side
Cable
23