Sony SNC-CH140 Prospecto (en)

Descargar
4-174-240-11 (1)
Network Camera
Installation Manual
Before operating the unit, please read this manual thoroughly and 
retain it for future reference.
 
SNC-CH140 
Owner’s Record
The model and serial numbers are located on the top. Record these numbers 
in the spaces provided below.
Refer to these numbers whenever you call upon your Sony dealer regarding 
this product.
Model No. 
 Serial No. 
WARNING
To reduce a risk of fire or electric shock, do not expose 
this product to rain or moisture.
To avoid electrical shock, do not open the cabinet. Refer 
servicing to qualified personnel only. 
WARNING
This installation should be made by a qualified service person and should 
conform to all local codes.
WARNING
A readily accessible disconnect device shall be incorporated in the building 
installation wiring.
WARNING (for Installers only)
Instructions for installing the equipment on the ceiling or the wall:
After the installation, ensure the connection is capable of supporting at least 
a force of 50 Newtons (N) downwards.
CAUTION for LAN port
For safety reason, do not connect the LAN port to any network devices that 
might have excessive voltage.
The LAN port of this unit is to be connected only to the devices whose 
power feeding meets the requirements for SELV (Safety Extra Low Voltage) 
and complies with Limited Power Source according to IEC 60950-1 Second 
Edition.
Power Supply
Caution for U.S.A. and Canada
The SNC-CH140 operates on 24V AC or 12V DC.
The SNC-CH140 automatically detects the power.
In the USA, this product shall be powered by a UL listed Class 2 Power Supply 
Only.
In Canada, this product shall be powered by a CSA Certified Class 2 Power 
Supply Only.
Caution for other countries
The SNC-CH140 operates on 24V AC or 12V DC.
The SNC-CH140 automatically detects the power.
Use a power supply rated 24 V AC or 12 V DC which meets the requirements 
for SELV (Safety Extra Low Voltage) and complies with Limited Power Source 
according to IEC 60950-1 Second Edition.
For customers in the U.S.A.
This device complies with Part 15 of the FCC Rules. Operation is subject 
to the following two conditions: (1) This device may not cause harmful 
interference, and (2) this device must accept any interference received, 
including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits 
for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits 
are designed to provide reasonable protection against harmful interference 
when the equipment is operated in a commercial environment. This 
equipment generates, uses, and can radiate radio frequency energy and, if 
not installed and used in accordance with the instruction manual, may cause 
harmful interference to radio communications. Operation of this equipment 
in a residential area is likely to cause harmful interference in which case the 
user will be required to correct the interference at his own expense.
You are cautioned that any changes or modifications not expressly approved 
in this manual could void your authority to operate this equipment.
All interface cables used to connect peripherals must be shielded in order to 
comply with the limits for a digital device pursuant to Subpart B or Part 15 of 
FCC Rules.
For customers in Canada
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du 
Canada.
For the customers in Europe
The manufacturer of this product is Sony Corporation, 1-7-1 Konan, Minato-
ku, Tokyo, Japan.
The Authorized Representative for EMC and product safety is Sony 
Deutschland GmbH, Hedelfinger Strasse 61, 70327 Stuttgart, Germany. 
For any service or guarantee matters please refer to the addresses given in 
separate service or guarantee documents.
For the customers in Europe, Australia and New Zealand
WARNING
This is a Class A product. In a domestic environment, this product may cause 
radio interference in which case the user may be required to take adequate 
measures.
In the case that interference should occur, consult your nearest authorized 
Sony service facility.
This apparatus shall not be used in the residential area.
ATTENTION
The electromagnetic fields at specific frequencies may influence the picture 
of the unit.
Notes on Use
Before Use
If you find condensation when you open the package, turn on the power after 
leaving it for about 60 minutes.
Data and security
You should keep in mind that the images or audio you are monitoring may be 
protected by privacy and other legal rights, and the responsibility for making 
sure you are complying with applicable laws is yours alone. 
Access to the images and audio is protected only by a user name and the 
password you set up. No further authentication is provided nor should you 
presume that any other protective filtering is done by the service. Since 
the service is Internet-based, there is a risk that the image or audio you are 
monitoring can be viewed or used by a third-party via the network.
SONY IS NOT RESPONSIBLE, AND ASSUMES ABSOLUTELY NO LIABILITY TO YOU 
OR ANYONE ELSE, FOR SERVICE INTERRUPTIONS OR DISCONTINUATIONS OR 
EVEN SERVICE CANCELLATION. THE SERVICE IS PROVIDED AS-IS, AND SONY 
DISCLAIMS AND EXCLUDES ALL WARRANTIES, EXPRESS OR IMPLIED, WITH 
RESPECT TO THE SERVICE INCLUDING, BUT NOT LIMITED TO, ANY OR ALL 
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR 
PURPOSE, OR THAT IT WILL OPERATE ERROR-FREE OR CONTINUOUSLY.
Security configuration is essential for wireless LAN. Should a problem 
occur without setting security, or due to the limitation of the wireless LAN 
specifications, SONY shall not be liable for any damage, loss of recorded data 
or restoration thereof.
Always make a test recording, and verify that it was recorded successfully. 
SONY WILL NOT BE LIABLE FOR DAMAGES OF ANY KIND INCLUDING, BUT NOT 
LIMITED TO, COMPENSATION OR REIMBURSEMENT ON ACCOUNT OF FAILURE 
OF THIS UNIT OR ITS RECORDING MEDIA, EXTERNAL STORAGE SYSTEMS OR 
ANY OTHER MEDIA OR STORAGE SYSTEMS TO RECORD CONTENT OF ANY TYPE.
Always verify that the unit is operating properly before use. SONY WILL NOT 
BE LIABLE FOR DAMAGES OF ANY KIND INCLUDING, BUT NOT LIMITED TO, 
COMPENSATION OR REIMBURSEMENT ON ACCOUNT OF THE LOSS OF PRESENT 
OR PROSPECTIVE PROFITS DUE TO FAILURE OF THIS UNIT, EITHER DURING THE 
WARRANTY PERIOD OR AFTER EXPIRATION OF THE WARRANTY, OR FOR ANY 
OTHER REASON WHATSOEVER.
If you lose data by using this unit, SONY accepts no responsibility for 
restoration of the data.
Personal information
The images taken by the system using this device can identify individuals 
and thus they fall under “personal information” stipulated in the “Act on 
the Protection of Personal Information”. Please handle the video data 
appropriately according to law.
Information recorded using this product may also be “personal information”. 
Upon disposal, transfer, repair, or any other occasion where this product or 
storage media is passed on to a third party, practice due care in its handling.
Operating or storage location
Avoid operating or storing the camera in the following locations.
Extremely hot or cold places (Operating temperature: –10°C to +50°C [14°F to 
122°F])
Exposed to direct sunlight for a long time, or close to heating equipment (e.g., 
near heaters)
Close to sources of strong magnetism
Close to sources of powerful electromagnetic radiation, such as radios or TV 
transmitters
Locations subject to strong vibration or shock
Ventilation
To prevent heat buildup, do not block air circulation around the camera.
Transportation
Always turn off the power when carrying.
When transporting the camera, repack it as originally packed at the factory or 
in materials of equal quality.
Cleaning
Use a blower to remove dust from the lens.
Use a soft, dry cloth to clean the external surfaces of the camera. Stubborn 
stains can be removed using a soft cloth dampened with a small quantity of 
detergent solution, then wipe dry.
Do not use volatile solvents such as alcohol, benzene or thinners as they may 
damage the surface finishes.
Note on laser beams
Laser beams may damage image sensors. You are cautioned that the surface of image 
sensors should not be exposed to laser beam radiation in an environment where a laser 
beam device is used.
Phenomena Specific to Image Sensors
The following phenomena that may occur in images are specific to image 
sensors. They do not indicate a malfunction.
White flecks
Although the image sensors are produced with high-precision technologies, fine 
white flecks may be generated on the screen in rare cases, caused by cosmic rays, 
etc.
This is related to the principle of image sensors and is not a malfunction.
The white flecks especially tend to be seen in the following cases:
- when operating at a high environmental temperature
- when you have raised the gain (sensitivity)
- when using the slow shutter
Aliasing
When fine patterns, stripes, or lines are shot, they may appear jagged or flicker.
About the Supplied Manuals
Installation Manual (this document)
This Installation Manual describes the names and functions of parts and controls 
of the Network Camera, gives connection examples and explains how to set up 
the camera. Be sure to read the Installation Manual before operating.
User’s Guide (stored in the CD-ROM)
The User’s Guide describes how to set up the camera and how to control the 
camera via a Web browser.
After installing and connecting the camera correctly, operate referring to this 
User’s Guide.
Using the CD-ROM Manuals
The supplied CD-ROM disc includes the User’s Guides for this unit in PDF format.
Preparations
The Adobe Reader Version 6.0 or higher must be installed on your computer in 
order to use the guides stored in the CD-ROM disc. 
Note 
If Adobe Reader is not installed, it may be downloaded from the following URL:  
http://www.adobe.com/
Reading the manual in the CD-ROM
1
  Insert the CD-ROM in your CD-ROM drive.
 
A cover page appears automatically in your Web browser. 
If it does not appear automatically in the Web browser, double-click on the 
index.htm file on the CD-ROM.
2
  Select and click on the manual that you want to read.
 
This opens the PDF file of the manual. 
Clicking an item in the Table of Contents allows you jump to the relevant 
page.
Notes 
The files may not be displayed properly, depending on the version of Adobe 
Reader. In this case, install the latest version, which you can download from 
the URL mentioned in “Preparations” above.
If you have lost or damaged the CD-ROM, you can purchase replacement.  
Contact your Sony service representative.
Adobe and Acrobat Reader are trademarks of Adobe Systems Incorporated in the 
United States and/or other countries.
Location and Function of Part
Front 
  Lens
A vari-focal lens for 1/3 type is mounted as standard equipment.
  Focus ring
Turn this ring toward N (near) to focus on a closer object. Turn it toward F 
(infinite) to focus on a farther object.
  Zoom ring
Turn this ring toward T for telephoto, or toward W for wide-angle.
  Tripod screw hole
Use this screw hole when attaching the camera 
to a tripod (screw: 1/4”, 20 UNC). You can attach a 
tripod to either the top or bottom of the camera.
Caution
Use the mounting screw whose length is 4.5 mm – 7 mm only. Use of 
other screws may cause improper mounting and damage parts inside 
the camera.
  Rating Label
This label shows the name of device and its electric rating.
  Lens connector (4-pin socket)
Supplies power and control signals to an auto-iris lens.
Rear 
  DC 12 V/AC 24 V (power input) terminal
Connect to a 12V DC or 24V AC power supply system.
  LAN network port (RJ-45)
Connect to a hub on the 10BASE-T/100BASE-TX network using a network 
cable (UTP, category 5).
Refer to “Connecting the power source” on the reverse side for PoE 
connection.
  Easy Focus button
Press this button to automatically adjust the focus.
To load the default setting, press and hold this button for 4 seconds.
  Fall-prevention wire rope mounting screw hole
When installing the camera to the ceiling or the wall, secure the supplied 
fall-prevention wire rope to this hole using the supplied shoulder screw.
  VIDEO OUT (video output) connector
Connect the BNC cable (not supplied) to this connector.
Note
The output image is mainly used to adjust the view angle, and may not 
display correctly, depending on the video format and image size settings. 
The image may not display properly in the horizontal and/or vertical 
plane.
The image may be reduced.
  U (ground) terminal
This is a ground terminal for the chassis.
  CF card lever 
Press the lever to remove the CF memory card** from the CF card slot.
  CF card slot
This slot is used for the optional SNCA-CFW5* wireless card or CF 
memory card**.
Insert the SNCA-CFW5* into the slot and attach the optional wireless LAN 
antenna SNCA-AN1* to the camera to extend the communicable distance 
by wireless LAN.
Notes
Insert the CF memory card with its bottom side facing the camera’ 
NETWORK indicator.
*   SNCA-CFW5 and SNCA-AN1 are not available in some countries and 
areas. For details, contact your authorized Sony dealer.
**  For inquiries regarding verified CF memory cards, contact your 
authorized Sony dealer.
  CF card slot cover 
To remove the CF card slot cover, pull the cover forward.
When reinstalling the CF card slot cover, be sure the cover is completely 
closed.
  NTSC/PAL switch
Switching the video output. 
  I/O (Input/Output) port
This cable is provided with a sensor input and two alarm outputs.
The wires of the cable control the following signals.
PinNo. 
Signal
1
Sensor input+ 
2
Sensor input– (GND) 
3
Alarm output 1+
4
Alarm output 1–
5
Alarm output 2+
6
Alarm output 2–
For details on each function and required settings, see the User’s Guide stored 
in the supplied CD-ROM.
For the wiring, see “Connecting the I/O cable.”
   (line output) jack (minijack, monaural)
Connect a commercially available speaker system with a built-in 
amplifier.
  POWER indicator (Green)
When the power is supplied to the camera, the camera starts checking 
the system. If the system is normal, this indicator lights up. If a system 
error occurs, this indicator flashes every second. In this case, consult your 
authorized Sony dealer.
  m (microphone input) jack (minijack, monaural)
Connect a commercially available microphone. This jack supports plug-
in-power microphones (rated voltage: 2.5 V DC).
  NETWORK indicator (green/orange)
The indicator lights up or flashes when the camera is connected to the 
network. The indicator is off when the camera is not connected to the 
network. When 100BASE-TX is connected, the indicator turns green. 
When 10BASE-T is connected, the indicator turns orange.
  Reset switch
To reset the camera to the factory default settings, turn on the power to 
the camera while holding down this switch with a pointed object.
(continued on the reverse side)
 2009 Sony Corporation    
Printed in China
U1/4”, 20 UNC
 = 4.5 mm - 7 mm
(ISO standard) (with the
screws fastened)